Product Carousel Tabs
Strainers
Lab Mechanical Crusher
For preparation of wood meal, wood samples for chemical analysis and
grinding virtually any material to produce a finely meshed sample.
grinding virtually any material to produce a finely meshed sample.
Four blade rotor dia 200mm operating at 400 to 800 rpm.
Interchangeable screen mesh available as per requirement.
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCLMC – 200
SKU: *Model No: UCLMC - 200
Strainers
Smoothness Tester (Bendtsen Type)
This instrument is used for testing the average smoothness, porosity
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
under
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
Attachment:
*Template for specimen prepration
*4.5 digit SSD timer
*Power required: 220 VAC, 50 Hz
*Model No: UCSPS – G
SKU: *Model No: UCSPS - G
Strainers
Stiffness Tester (Taber Type)
This instrument used to measure the stiffness of paper, card board,
plastic, light metal sheet, foil & other flexible material. A test piece
easily clamp from one side. To determine the maximum force by lower
end clamp on a rotating disc then specimen is bent by 50 degree at a
constant speed. The stiffness of the material is determined by rotation
are clock wise and anti clock wise. So that average stiffness can be
measured in both directions
plastic, light metal sheet, foil & other flexible material. A test piece
easily clamp from one side. To determine the maximum force by lower
end clamp on a rotating disc then specimen is bent by 50 degree at a
constant speed. The stiffness of the material is determined by rotation
are clock wise and anti clock wise. So that average stiffness can be
measured in both directions
*Range: 0 – 5000 Taber stiffness unit
*Range: 0 – 5000 Taber stiffness unit
*Cabinet structure: Aluminium
*Attachment: Triple shear cutter for specimen prepration
*Power required: 220 VAC, 50 Hz
*ModelNo:UCST-5000T
SKU: *ModelNo:UCST-5000T
Strainers
Electronic Stiffness Tester
This instrument used to measure the stiffness of paper board by determining
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
*Digital read out for Bending Force,
*Range: 0 – 10000mN *Mechanical structure: Aluminium
*Load Cell: Max load *Cabinet structure: Aluminium
*Attachment: Triple shear cutter for specimen prepration
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*ModelNo:UCST-10000D
SKU: *ModelNo:UCST-10000D
Strainers
Folding Endurance Tester (Kohier Mollin Type)
The tester is used for measuring the no. Folds in paper, paper board &
films with a standard folding speed per minute. Folding endurance tester
with SSD counter measure the no. of double fold
and its hold when the paper break automatically. A test piece is fastened
vertically between two clamps. The upper clamp folds, the test piece by
means of the reciprocating circular motion while the lower clamp
maintain it under a given load. The loading clamps of dead weight type,
giving standard load of 800 gm
films with a standard folding speed per minute. Folding endurance tester
with SSD counter measure the no. of double fold
and its hold when the paper break automatically. A test piece is fastened
vertically between two clamps. The upper clamp folds, the test piece by
means of the reciprocating circular motion while the lower clamp
maintain it under a given load. The loading clamps of dead weight type,
giving standard load of 800 gm
*Attachment: Die & punch strip cutter 15x100mm for specimen
*Power required: 220 VAC, 50 Hz
*Model No: UCFET- 200
SKU: *Model No: UCFET- 200
Strainers
Fluff Tester (Patra Type)
A sample is placed between the blanket and is steel roll and is moved between
the roles under nip pressure. After selected number of sheets have been
passed the fluff is transferred to blanket cylinders and a linen counter moved is
at the top of the machine to count the numbers of particles & fibre adhessive to
a given area of blanket. The tester enables fluff to be measured easily after
stimulating the action of printing press using a dry blanket. It is based on the
concept of PATRA. The tester is capable of giving reproducible results and the
fluff build-up proceeds at a steady rate with a number of sheets.
the roles under nip pressure. After selected number of sheets have been
passed the fluff is transferred to blanket cylinders and a linen counter moved is
at the top of the machine to count the numbers of particles & fibre adhessive to
a given area of blanket. The tester enables fluff to be measured easily after
stimulating the action of printing press using a dry blanket. It is based on the
concept of PATRA. The tester is capable of giving reproducible results and the
fluff build-up proceeds at a steady rate with a number of sheets.
*Model No: UCFT – P
SKU: *Model No: UCFT - P
Strainers
Thickness Micrometer (Bulk Tester
The thickness of sheet is meas*Automatic dead weight with time control deviceured as distance between two
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
*Motorized operated.
*Automatic dead weight with time control device
*Maximum thickness range: 10 mm
*Resolution: 1 Micron/0.001 mm
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCTMB – 10D
SKU: *Model No: UCTMB - 10D
Strainers
Tearing Resistance Tester (Elmendorff Type)
This instrument is used for measuring the tensile of paper, Paper board, plastic
& film. This is the high quality tensile tester is intended for testing tensile
strength in printing. It is expected to be an excellent alternative for all customer
The tensile tester consist of a mechanical strain system with greatest accuracy
having two strain jaws of which the top one is firm and the lower one is movable
and connected to a load cell.
& film. This is the high quality tensile tester is intended for testing tensile
strength in printing. It is expected to be an excellent alternative for all customer
The tensile tester consist of a mechanical strain system with greatest accuracy
having two strain jaws of which the top one is firm and the lower one is movable
and connected to a load cell.
*Capacity: 200 Newton.
*Microprocessor based
*Digital read out for tensile strength, *Tensile force
*Breaking length *Elongation.
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz *Model No: UCTT – 200DM
*Microprocessor based
*Digital read out for tensile strength, *Tensile force
*Breaking length *Elongation.
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz *Model No: UCTT – 200DM
SKU: 5487FB8/44
Strainers
Digital Oil Penetration Tester (William Type)
This instrument is used for determining the penetration time of oil and
other liquids through paper and other similar materials used for
lamination purpose. Provided with cooling system, Electronic PID control
for constant temperature regulating
other liquids through paper and other similar materials used for
lamination purpose. Provided with cooling system, Electronic PID control
for constant temperature regulating
Attachment: Electronic self starting timer for time measurement of
penetration time in seconds,
penetration time in seconds,
*Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCCOP – 100D
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCCOP – 100D
SKU: *Model No: UCCOP - 100D
Strainers
Paper Surface Oil Absorbency Tester (Pira Type)
This instrument is used for determining the oil absorption of the surface of
paper and paperboard with Electronic self starting timer. A specimen is
placed on a inclined plane surface covered with rubber offset blanket, the
standard oil drops on brass roller and is rolled against the rubber blanket
and the oil film on brass roller is transferred to the specimen surface. The
oil absorption time is measured in second.
Attachment: *Electronic self starting timer for time measurement of
absorption time in seconds
paper and paperboard with Electronic self starting timer. A specimen is
placed on a inclined plane surface covered with rubber offset blanket, the
standard oil drops on brass roller and is rolled against the rubber blanket
and the oil film on brass roller is transferred to the specimen surface. The
oil absorption time is measured in second.
Attachment: *Electronic self starting timer for time measurement of
absorption time in seconds
*Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCSOA – 9999D
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCSOA – 9999D
SKU: 5487FB8/38
Strainers
Internal Ply Bond Tester (Scott Type)face Oil Absorbency Tester (Pira Type)
The instrument designed for determining the internal bonding strength
of paper paperboard and laminates etc, by measuring the average
energy in thousands of foot pound required to de-laminate the specimen
in two piles as described reference standard TAPPI T-569 Dual capacity
pendulum of 0-0.25 FT/LB and 0.1-0.5 Ft/Lb. Readings directly on
calibrated scale. The five number specimen preparation unit which will
allow for variations of specimen thicknesses, with different clamping
pressure on the specimenfrom 50 to 200 PSI
of paper paperboard and laminates etc, by measuring the average
energy in thousands of foot pound required to de-laminate the specimen
in two piles as described reference standard TAPPI T-569 Dual capacity
pendulum of 0-0.25 FT/LB and 0.1-0.5 Ft/Lb. Readings directly on
calibrated scale. The five number specimen preparation unit which will
allow for variations of specimen thicknesses, with different clamping
pressure on the specimenfrom 50 to 200 PSI
Attachment: *Standard calibration sliding weight with sample holder
*Double side adhesive tape width 25 mm
*ModelNo:UCPBT-5A
*ModelNo:UCPBT-5A
SKU: *ModelNo:UCPBT-5A
Strainers
Digital Internal Ply Bond tester
This instrument is used for determining the internal bonding strength of
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
*Attachment: Double side adhesive tape width 25 mm
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
SKU: *Model No: UCPBT - 5D
Strainers
Lab Mechanical Crusher
For preparation of wood meal, wood samples for chemical analysis and
grinding virtually any material to produce a finely meshed sample.
grinding virtually any material to produce a finely meshed sample.
Four blade rotor dia 200mm operating at 400 to 800 rpm.
Interchangeable screen mesh available as per requirement.
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCLMC – 200
SKU: *Model No: UCLMC - 200
Strainers
Smoothness Tester (Bendtsen Type)
This instrument is used for testing the average smoothness, porosity
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
under
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
Attachment:
*Template for specimen prepration
*4.5 digit SSD timer
*Power required: 220 VAC, 50 Hz
*Model No: UCSPS – G
SKU: *Model No: UCSPS - G
Strainers
Stiffness Tester (Taber Type)
This instrument used to measure the stiffness of paper, card board,
plastic, light metal sheet, foil & other flexible material. A test piece
easily clamp from one side. To determine the maximum force by lower
end clamp on a rotating disc then specimen is bent by 50 degree at a
constant speed. The stiffness of the material is determined by rotation
are clock wise and anti clock wise. So that average stiffness can be
measured in both directions
plastic, light metal sheet, foil & other flexible material. A test piece
easily clamp from one side. To determine the maximum force by lower
end clamp on a rotating disc then specimen is bent by 50 degree at a
constant speed. The stiffness of the material is determined by rotation
are clock wise and anti clock wise. So that average stiffness can be
measured in both directions
*Range: 0 – 5000 Taber stiffness unit
*Range: 0 – 5000 Taber stiffness unit
*Cabinet structure: Aluminium
*Attachment: Triple shear cutter for specimen prepration
*Power required: 220 VAC, 50 Hz
*ModelNo:UCST-5000T
SKU: *ModelNo:UCST-5000T
Strainers
Electronic Stiffness Tester
This instrument used to measure the stiffness of paper board by determining
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
*Digital read out for Bending Force,
*Range: 0 – 10000mN *Mechanical structure: Aluminium
*Load Cell: Max load *Cabinet structure: Aluminium
*Attachment: Triple shear cutter for specimen prepration
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*ModelNo:UCST-10000D
SKU: *ModelNo:UCST-10000D
Strainers
Folding Endurance Tester (Kohier Mollin Type)
The tester is used for measuring the no. Folds in paper, paper board &
films with a standard folding speed per minute. Folding endurance tester
with SSD counter measure the no. of double fold
and its hold when the paper break automatically. A test piece is fastened
vertically between two clamps. The upper clamp folds, the test piece by
means of the reciprocating circular motion while the lower clamp
maintain it under a given load. The loading clamps of dead weight type,
giving standard load of 800 gm
films with a standard folding speed per minute. Folding endurance tester
with SSD counter measure the no. of double fold
and its hold when the paper break automatically. A test piece is fastened
vertically between two clamps. The upper clamp folds, the test piece by
means of the reciprocating circular motion while the lower clamp
maintain it under a given load. The loading clamps of dead weight type,
giving standard load of 800 gm
*Attachment: Die & punch strip cutter 15x100mm for specimen
*Power required: 220 VAC, 50 Hz
*Model No: UCFET- 200
SKU: *Model No: UCFET- 200
Strainers
Fluff Tester (Patra Type)
A sample is placed between the blanket and is steel roll and is moved between
the roles under nip pressure. After selected number of sheets have been
passed the fluff is transferred to blanket cylinders and a linen counter moved is
at the top of the machine to count the numbers of particles & fibre adhessive to
a given area of blanket. The tester enables fluff to be measured easily after
stimulating the action of printing press using a dry blanket. It is based on the
concept of PATRA. The tester is capable of giving reproducible results and the
fluff build-up proceeds at a steady rate with a number of sheets.
the roles under nip pressure. After selected number of sheets have been
passed the fluff is transferred to blanket cylinders and a linen counter moved is
at the top of the machine to count the numbers of particles & fibre adhessive to
a given area of blanket. The tester enables fluff to be measured easily after
stimulating the action of printing press using a dry blanket. It is based on the
concept of PATRA. The tester is capable of giving reproducible results and the
fluff build-up proceeds at a steady rate with a number of sheets.
*Model No: UCFT – P
SKU: *Model No: UCFT - P
Strainers
Thickness Micrometer (Bulk Tester
The thickness of sheet is meas*Automatic dead weight with time control deviceured as distance between two
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
*Motorized operated.
*Automatic dead weight with time control device
*Maximum thickness range: 10 mm
*Resolution: 1 Micron/0.001 mm
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCTMB – 10D
SKU: *Model No: UCTMB - 10D
Strainers
Tearing Resistance Tester (Elmendorff Type)
This instrument is used for measuring the tensile of paper, Paper board, plastic
& film. This is the high quality tensile tester is intended for testing tensile
strength in printing. It is expected to be an excellent alternative for all customer
The tensile tester consist of a mechanical strain system with greatest accuracy
having two strain jaws of which the top one is firm and the lower one is movable
and connected to a load cell.
& film. This is the high quality tensile tester is intended for testing tensile
strength in printing. It is expected to be an excellent alternative for all customer
The tensile tester consist of a mechanical strain system with greatest accuracy
having two strain jaws of which the top one is firm and the lower one is movable
and connected to a load cell.
*Capacity: 200 Newton.
*Microprocessor based
*Digital read out for tensile strength, *Tensile force
*Breaking length *Elongation.
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz *Model No: UCTT – 200DM
*Microprocessor based
*Digital read out for tensile strength, *Tensile force
*Breaking length *Elongation.
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz *Model No: UCTT – 200DM
SKU: 5487FB8/44
Strainers
Digital Oil Penetration Tester (William Type)
This instrument is used for determining the penetration time of oil and
other liquids through paper and other similar materials used for
lamination purpose. Provided with cooling system, Electronic PID control
for constant temperature regulating
other liquids through paper and other similar materials used for
lamination purpose. Provided with cooling system, Electronic PID control
for constant temperature regulating
Attachment: Electronic self starting timer for time measurement of
penetration time in seconds,
penetration time in seconds,
*Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCCOP – 100D
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCCOP – 100D
SKU: *Model No: UCCOP - 100D
Strainers
Paper Surface Oil Absorbency Tester (Pira Type)
This instrument is used for determining the oil absorption of the surface of
paper and paperboard with Electronic self starting timer. A specimen is
placed on a inclined plane surface covered with rubber offset blanket, the
standard oil drops on brass roller and is rolled against the rubber blanket
and the oil film on brass roller is transferred to the specimen surface. The
oil absorption time is measured in second.
Attachment: *Electronic self starting timer for time measurement of
absorption time in seconds
paper and paperboard with Electronic self starting timer. A specimen is
placed on a inclined plane surface covered with rubber offset blanket, the
standard oil drops on brass roller and is rolled against the rubber blanket
and the oil film on brass roller is transferred to the specimen surface. The
oil absorption time is measured in second.
Attachment: *Electronic self starting timer for time measurement of
absorption time in seconds
*Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCSOA – 9999D
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCSOA – 9999D
SKU: 5487FB8/38
Strainers
Internal Ply Bond Tester (Scott Type)face Oil Absorbency Tester (Pira Type)
The instrument designed for determining the internal bonding strength
of paper paperboard and laminates etc, by measuring the average
energy in thousands of foot pound required to de-laminate the specimen
in two piles as described reference standard TAPPI T-569 Dual capacity
pendulum of 0-0.25 FT/LB and 0.1-0.5 Ft/Lb. Readings directly on
calibrated scale. The five number specimen preparation unit which will
allow for variations of specimen thicknesses, with different clamping
pressure on the specimenfrom 50 to 200 PSI
of paper paperboard and laminates etc, by measuring the average
energy in thousands of foot pound required to de-laminate the specimen
in two piles as described reference standard TAPPI T-569 Dual capacity
pendulum of 0-0.25 FT/LB and 0.1-0.5 Ft/Lb. Readings directly on
calibrated scale. The five number specimen preparation unit which will
allow for variations of specimen thicknesses, with different clamping
pressure on the specimenfrom 50 to 200 PSI
Attachment: *Standard calibration sliding weight with sample holder
*Double side adhesive tape width 25 mm
*ModelNo:UCPBT-5A
*ModelNo:UCPBT-5A
SKU: *ModelNo:UCPBT-5A
Strainers
Digital Internal Ply Bond tester
This instrument is used for determining the internal bonding strength of
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
*Attachment: Double side adhesive tape width 25 mm
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
SKU: *Model No: UCPBT - 5D
Strainers
Lab Mechanical Crusher
For preparation of wood meal, wood samples for chemical analysis and
grinding virtually any material to produce a finely meshed sample.
grinding virtually any material to produce a finely meshed sample.
Four blade rotor dia 200mm operating at 400 to 800 rpm.
Interchangeable screen mesh available as per requirement.
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCLMC – 200
SKU: *Model No: UCLMC - 200
Strainers
Smoothness Tester (Bendtsen Type)
This instrument is used for testing the average smoothness, porosity
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
under
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
Attachment:
*Template for specimen prepration
*4.5 digit SSD timer
*Power required: 220 VAC, 50 Hz
*Model No: UCSPS – G
SKU: *Model No: UCSPS - G
Strainers
Stiffness Tester (Taber Type)
This instrument used to measure the stiffness of paper, card board,
plastic, light metal sheet, foil & other flexible material. A test piece
easily clamp from one side. To determine the maximum force by lower
end clamp on a rotating disc then specimen is bent by 50 degree at a
constant speed. The stiffness of the material is determined by rotation
are clock wise and anti clock wise. So that average stiffness can be
measured in both directions
plastic, light metal sheet, foil & other flexible material. A test piece
easily clamp from one side. To determine the maximum force by lower
end clamp on a rotating disc then specimen is bent by 50 degree at a
constant speed. The stiffness of the material is determined by rotation
are clock wise and anti clock wise. So that average stiffness can be
measured in both directions
*Range: 0 – 5000 Taber stiffness unit
*Range: 0 – 5000 Taber stiffness unit
*Cabinet structure: Aluminium
*Attachment: Triple shear cutter for specimen prepration
*Power required: 220 VAC, 50 Hz
*ModelNo:UCST-5000T
SKU: *ModelNo:UCST-5000T
Strainers
Electronic Stiffness Tester
This instrument used to measure the stiffness of paper board by determining
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
*Digital read out for Bending Force,
*Range: 0 – 10000mN *Mechanical structure: Aluminium
*Load Cell: Max load *Cabinet structure: Aluminium
*Attachment: Triple shear cutter for specimen prepration
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*ModelNo:UCST-10000D
SKU: *ModelNo:UCST-10000D
Strainers
Folding Endurance Tester (Kohier Mollin Type)
The tester is used for measuring the no. Folds in paper, paper board &
films with a standard folding speed per minute. Folding endurance tester
with SSD counter measure the no. of double fold
and its hold when the paper break automatically. A test piece is fastened
vertically between two clamps. The upper clamp folds, the test piece by
means of the reciprocating circular motion while the lower clamp
maintain it under a given load. The loading clamps of dead weight type,
giving standard load of 800 gm
films with a standard folding speed per minute. Folding endurance tester
with SSD counter measure the no. of double fold
and its hold when the paper break automatically. A test piece is fastened
vertically between two clamps. The upper clamp folds, the test piece by
means of the reciprocating circular motion while the lower clamp
maintain it under a given load. The loading clamps of dead weight type,
giving standard load of 800 gm
*Attachment: Die & punch strip cutter 15x100mm for specimen
*Power required: 220 VAC, 50 Hz
*Model No: UCFET- 200
SKU: *Model No: UCFET- 200
Strainers
Fluff Tester (Patra Type)
A sample is placed between the blanket and is steel roll and is moved between
the roles under nip pressure. After selected number of sheets have been
passed the fluff is transferred to blanket cylinders and a linen counter moved is
at the top of the machine to count the numbers of particles & fibre adhessive to
a given area of blanket. The tester enables fluff to be measured easily after
stimulating the action of printing press using a dry blanket. It is based on the
concept of PATRA. The tester is capable of giving reproducible results and the
fluff build-up proceeds at a steady rate with a number of sheets.
the roles under nip pressure. After selected number of sheets have been
passed the fluff is transferred to blanket cylinders and a linen counter moved is
at the top of the machine to count the numbers of particles & fibre adhessive to
a given area of blanket. The tester enables fluff to be measured easily after
stimulating the action of printing press using a dry blanket. It is based on the
concept of PATRA. The tester is capable of giving reproducible results and the
fluff build-up proceeds at a steady rate with a number of sheets.
*Model No: UCFT – P
SKU: *Model No: UCFT - P
Strainers
Thickness Micrometer (Bulk Tester
The thickness of sheet is meas*Automatic dead weight with time control deviceured as distance between two
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
*Motorized operated.
*Automatic dead weight with time control device
*Maximum thickness range: 10 mm
*Resolution: 1 Micron/0.001 mm
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCTMB – 10D
SKU: *Model No: UCTMB - 10D
Strainers
Tearing Resistance Tester (Elmendorff Type)
This instrument is used for measuring the tensile of paper, Paper board, plastic
& film. This is the high quality tensile tester is intended for testing tensile
strength in printing. It is expected to be an excellent alternative for all customer
The tensile tester consist of a mechanical strain system with greatest accuracy
having two strain jaws of which the top one is firm and the lower one is movable
and connected to a load cell.
& film. This is the high quality tensile tester is intended for testing tensile
strength in printing. It is expected to be an excellent alternative for all customer
The tensile tester consist of a mechanical strain system with greatest accuracy
having two strain jaws of which the top one is firm and the lower one is movable
and connected to a load cell.
*Capacity: 200 Newton.
*Microprocessor based
*Digital read out for tensile strength, *Tensile force
*Breaking length *Elongation.
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz *Model No: UCTT – 200DM
*Microprocessor based
*Digital read out for tensile strength, *Tensile force
*Breaking length *Elongation.
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz *Model No: UCTT – 200DM
SKU: 5487FB8/44
Strainers
Digital Oil Penetration Tester (William Type)
This instrument is used for determining the penetration time of oil and
other liquids through paper and other similar materials used for
lamination purpose. Provided with cooling system, Electronic PID control
for constant temperature regulating
other liquids through paper and other similar materials used for
lamination purpose. Provided with cooling system, Electronic PID control
for constant temperature regulating
Attachment: Electronic self starting timer for time measurement of
penetration time in seconds,
penetration time in seconds,
*Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCCOP – 100D
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCCOP – 100D
SKU: *Model No: UCCOP - 100D
Strainers
Paper Surface Oil Absorbency Tester (Pira Type)
This instrument is used for determining the oil absorption of the surface of
paper and paperboard with Electronic self starting timer. A specimen is
placed on a inclined plane surface covered with rubber offset blanket, the
standard oil drops on brass roller and is rolled against the rubber blanket
and the oil film on brass roller is transferred to the specimen surface. The
oil absorption time is measured in second.
Attachment: *Electronic self starting timer for time measurement of
absorption time in seconds
paper and paperboard with Electronic self starting timer. A specimen is
placed on a inclined plane surface covered with rubber offset blanket, the
standard oil drops on brass roller and is rolled against the rubber blanket
and the oil film on brass roller is transferred to the specimen surface. The
oil absorption time is measured in second.
Attachment: *Electronic self starting timer for time measurement of
absorption time in seconds
*Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCSOA – 9999D
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCSOA – 9999D
SKU: 5487FB8/38
Strainers
Internal Ply Bond Tester (Scott Type)face Oil Absorbency Tester (Pira Type)
The instrument designed for determining the internal bonding strength
of paper paperboard and laminates etc, by measuring the average
energy in thousands of foot pound required to de-laminate the specimen
in two piles as described reference standard TAPPI T-569 Dual capacity
pendulum of 0-0.25 FT/LB and 0.1-0.5 Ft/Lb. Readings directly on
calibrated scale. The five number specimen preparation unit which will
allow for variations of specimen thicknesses, with different clamping
pressure on the specimenfrom 50 to 200 PSI
of paper paperboard and laminates etc, by measuring the average
energy in thousands of foot pound required to de-laminate the specimen
in two piles as described reference standard TAPPI T-569 Dual capacity
pendulum of 0-0.25 FT/LB and 0.1-0.5 Ft/Lb. Readings directly on
calibrated scale. The five number specimen preparation unit which will
allow for variations of specimen thicknesses, with different clamping
pressure on the specimenfrom 50 to 200 PSI
Attachment: *Standard calibration sliding weight with sample holder
*Double side adhesive tape width 25 mm
*ModelNo:UCPBT-5A
*ModelNo:UCPBT-5A
SKU: *ModelNo:UCPBT-5A
Strainers
Digital Internal Ply Bond tester
This instrument is used for determining the internal bonding strength of
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
*Attachment: Double side adhesive tape width 25 mm
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
SKU: *Model No: UCPBT - 5D
PHYSICAL TESTING EQUIPMENTS
-
Strainers
Lab Mechanical Crusher
- For preparation of wood meal, wood samples for chemical analysis and
grinding virtually any material to produce a finely meshed sample. - Four blade rotor dia 200mm operating at 400 to 800 rpm.
- Interchangeable screen mesh available as per requirement.
- *Operating voltage: 220 VAC, 50 Hz
- *Model No: UCLMC – 200
SKU: *Model No: UCLMC - 200 - For preparation of wood meal, wood samples for chemical analysis and
-
Strainers
Smoothness Tester (Bendtsen Type)
- This instrument is used for testing the average smoothness, porosity
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample, - under
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen - Attachment:
- *Template for specimen prepration
- *4.5 digit SSD timer
- *Power required: 220 VAC, 50 Hz
- *Model No: UCSPS – G
SKU: *Model No: UCSPS - G - This instrument is used for testing the average smoothness, porosity
-
Strainers
Stiffness Tester (Taber Type)
- This instrument used to measure the stiffness of paper, card board,
plastic, light metal sheet, foil & other flexible material. A test piece
easily clamp from one side. To determine the maximum force by lower
end clamp on a rotating disc then specimen is bent by 50 degree at a
constant speed. The stiffness of the material is determined by rotation
are clock wise and anti clock wise. So that average stiffness can be
measured in both directions - *Range: 0 – 5000 Taber stiffness unit
- *Range: 0 – 5000 Taber stiffness unit
- *Cabinet structure: Aluminium
- *Attachment: Triple shear cutter for specimen prepration
- *Power required: 220 VAC, 50 Hz
- *ModelNo:UCST-5000T
SKU: *ModelNo:UCST-5000T - This instrument used to measure the stiffness of paper, card board,
-
Strainers
Electronic Stiffness Tester
- This instrument used to measure the stiffness of paper board by determining
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree. - *Digital read out for Bending Force,
- *Range: 0 – 10000mN *Mechanical structure: Aluminium
- *Load Cell: Max load *Cabinet structure: Aluminium
- *Attachment: Triple shear cutter for specimen prepration
- *Data transfer system through RS 232
- *Power required: 220 VAC, 50 Hz
- *ModelNo:UCST-10000D
SKU: *ModelNo:UCST-10000D - This instrument used to measure the stiffness of paper board by determining
-
Strainers
Folding Endurance Tester (Kohier Mollin Type)
- The tester is used for measuring the no. Folds in paper, paper board &
films with a standard folding speed per minute. Folding endurance tester
with SSD counter measure the no. of double fold
and its hold when the paper break automatically. A test piece is fastened
vertically between two clamps. The upper clamp folds, the test piece by
means of the reciprocating circular motion while the lower clamp
maintain it under a given load. The loading clamps of dead weight type,
giving standard load of 800 gm - *Attachment: Die & punch strip cutter 15x100mm for specimen
- *Power required: 220 VAC, 50 Hz
- *Model No: UCFET- 200
SKU: *Model No: UCFET- 200 - The tester is used for measuring the no. Folds in paper, paper board &
-
Strainers
Fluff Tester (Patra Type)
- A sample is placed between the blanket and is steel roll and is moved between
the roles under nip pressure. After selected number of sheets have been
passed the fluff is transferred to blanket cylinders and a linen counter moved is
at the top of the machine to count the numbers of particles & fibre adhessive to
a given area of blanket. The tester enables fluff to be measured easily after
stimulating the action of printing press using a dry blanket. It is based on the
concept of PATRA. The tester is capable of giving reproducible results and the
fluff build-up proceeds at a steady rate with a number of sheets. - *Model No: UCFT – P
SKU: *Model No: UCFT - P - A sample is placed between the blanket and is steel roll and is moved between
-
Strainers
Thickness Micrometer (Bulk Tester
- The thickness of sheet is meas*Automatic dead weight with time control deviceured as distance between two
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics. - *Motorized operated.
- *Automatic dead weight with time control device
- *Maximum thickness range: 10 mm
- *Resolution: 1 Micron/0.001 mm
- *Operating voltage: 220 VAC, 50 Hz
- *Model No: UCTMB – 10D
SKU: *Model No: UCTMB - 10D - The thickness of sheet is meas*Automatic dead weight with time control deviceured as distance between two
-
Strainers
Tearing Resistance Tester (Elmendorff Type)
- This instrument is used for measuring the tensile of paper, Paper board, plastic
& film. This is the high quality tensile tester is intended for testing tensile
strength in printing. It is expected to be an excellent alternative for all customer
The tensile tester consist of a mechanical strain system with greatest accuracy
having two strain jaws of which the top one is firm and the lower one is movable
and connected to a load cell. - *Capacity: 200 Newton.
*Microprocessor based
*Digital read out for tensile strength, *Tensile force
*Breaking length *Elongation.
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz *Model No: UCTT – 200DM
SKU: 5487FB8/44 - This instrument is used for measuring the tensile of paper, Paper board, plastic
-
Strainers
Digital Oil Penetration Tester (William Type)
- This instrument is used for determining the penetration time of oil and
other liquids through paper and other similar materials used for
lamination purpose. Provided with cooling system, Electronic PID control
for constant temperature regulating - Attachment: Electronic self starting timer for time measurement of
penetration time in seconds, - *Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCCOP – 100D
SKU: *Model No: UCCOP - 100D - This instrument is used for determining the penetration time of oil and
-
Strainers
Paper Surface Oil Absorbency Tester (Pira Type)
- This instrument is used for determining the oil absorption of the surface of
paper and paperboard with Electronic self starting timer. A specimen is
placed on a inclined plane surface covered with rubber offset blanket, the
standard oil drops on brass roller and is rolled against the rubber blanket
and the oil film on brass roller is transferred to the specimen surface. The
oil absorption time is measured in second.
Attachment: *Electronic self starting timer for time measurement of
absorption time in seconds - *Measuring range: 4.5 digit SSD Timer
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCSOA – 9999D
SKU: 5487FB8/38 - This instrument is used for determining the oil absorption of the surface of
-
Strainers
Internal Ply Bond Tester (Scott Type)face Oil Absorbency Tester (Pira Type)
- The instrument designed for determining the internal bonding strength
of paper paperboard and laminates etc, by measuring the average
energy in thousands of foot pound required to de-laminate the specimen
in two piles as described reference standard TAPPI T-569 Dual capacity
pendulum of 0-0.25 FT/LB and 0.1-0.5 Ft/Lb. Readings directly on
calibrated scale. The five number specimen preparation unit which will
allow for variations of specimen thicknesses, with different clamping
pressure on the specimenfrom 50 to 200 PSI - Attachment: *Standard calibration sliding weight with sample holder
- *Double side adhesive tape width 25 mm
*ModelNo:UCPBT-5A
SKU: *ModelNo:UCPBT-5A - The instrument designed for determining the internal bonding strength
-
Strainers
Digital Internal Ply Bond tester
- This instrument is used for determining the internal bonding strength of
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI - *Attachment: Double side adhesive tape width 25 mm
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
SKU: *Model No: UCPBT - 5D - This instrument is used for determining the internal bonding strength of
PACKAGING TESTING EQUIPMENTS
Strainers
Rapid Sheet Dryer
This instrument rapid sheet dryer is used for drying the wet pulp
& paper samples before determining the dry wet or moisture
content. It is provided with flat heating elements. Stainless steel
sheet fabricated chamber with insulating material ensure long
service
& paper samples before determining the dry wet or moisture
content. It is provided with flat heating elements. Stainless steel
sheet fabricated chamber with insulating material ensure long
service
*Automatic temperature control device
*Digital temperature Indicator cum controller
*S.S Make hole body chamber size: 10″ x 12″
*Double walled insulated with glass wool mat,
*Temperature range: 300°C
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCRSD – 1012
*Digital temperature Indicator cum controller
*S.S Make hole body chamber size: 10″ x 12″
*Double walled insulated with glass wool mat,
*Temperature range: 300°C
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCRSD – 1012
SKU: *Model No: UCRSD - 1012
Strainers
Ash Incinerator
This instrument is used for determining the ash content in paper,
Paperboard and other cellulosic materials, by burning an exactly
weighed quantity, and by obtaining the weight percentage of the
remain
Paperboard and other cellulosic materials, by burning an exactly
weighed quantity, and by obtaining the weight percentage of the
remain
Range: 800 °C
*Attachment: Digital temperature indicator cum controller
with 4.5 digit SSD.
with 4.5 digit SSD.
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCAI – 800D
SKU: 5487FB8/41
Strainers
Automatic Sheet Press
This instrument is used for pressing and de-watering of the hand
sheet quickly made on standard sheet making machine. Its must be
uniform pressure for the distribution of pulp across area
sheet quickly made on standard sheet making machine. Its must be
uniform pressure for the distribution of pulp across area
*Pneumatic sheet press control device
*Pressing time: 6-12 min adjustable
*Working pressure: 3.5 kg/cm2
*Size: 165mm, 200mm Squire
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCASP – 612
*Pressing time: 6-12 min adjustable
*Working pressure: 3.5 kg/cm2
*Size: 165mm, 200mm Squire
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCASP – 612
SKU: *Model No: UCASP - 612
Strainers
Paper Curl Tester
This instrument is used to measure the degree of curl when the paper
sample exposed, this method applies the principle of wetting one of the
paper and determining the maximum curvature or the time required to
reach maximum curvature the max. Curvature is an indication of relative
tendency of certain paper especially, to curl under normal of usage. The
time required to reach max. Curvature is measure of relative degree of
sizing such as secured with rosin.
sample exposed, this method applies the principle of wetting one of the
paper and determining the maximum curvature or the time required to
reach maximum curvature the max. Curvature is an indication of relative
tendency of certain paper especially, to curl under normal of usage. The
time required to reach max. Curvature is measure of relative degree of
sizing such as secured with rosin.
*Attachment: Template
*Model No: UCPCT – 90A
*Model No: UCPCT – 90A
SKU: *Model No: UCPCT - 90A
Strainers
Vibration Tester
This instrument is used for separating sieves and fiber flock from a
continuously fed pulp sample. Design approved by the technical section of the
British paper and board industry federation.
continuously fed pulp sample. Design approved by the technical section of the
British paper and board industry federation.
*Average capacity: 5kg dried pulp per hour.
*Stainer area: as per buyer requirement
*Screen slot: as per buyer requirement
*Attachment: Regulated speed controller
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCVT – 5A
*Stainer area: as per buyer requirement
*Screen slot: as per buyer requirement
*Attachment: Regulated speed controller
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCVT – 5A
SKU: *Model No: UCVT - 5A
Strainers
Digital Internal Ply Bond tester
This instrument is used for determining the internal bonding strength of
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
paper paperboard and laminates, by measuring the average energy, in
thousands of foot pound required to de-laminate the specimen in two
piles as described reference standard TAPPI T-569 The readings directly
indicate on Digital LCD Display. Take five samples for average reading
which will allow for variations of specimen thickness on the specimen
from 50 to 200 PSI
*Attachment: Double side adhesive tape width 25 mm
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
*Data transfer system Through RS 232
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPBT – 5D
SKU: *Model No: UCPBT - 5D
Strainers
Digital Pulp Disintegrator
This instrument is used for standardized disintegration of pulp to a
homogeneous suspension required for preparation of laboratory hand heet
and other purpose. Pivoted drive unit with stainless steel propeller and
shaft. The propeller is driven by electric motor via stepped timing belt,
which ensure a direct without slippage.
Attachment:
homogeneous suspension required for preparation of laboratory hand heet
and other purpose. Pivoted drive unit with stainless steel propeller and
shaft. The propeller is driven by electric motor via stepped timing belt,
which ensure a direct without slippage.
Attachment:
*Mechanical preset impulse counter on front panel for setting
desired number of revolution.
*Digital predetermination preset pulse counter on front panel for
setting desired number of revolution.
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPD – 2D
desired number of revolution.
*Digital predetermination preset pulse counter on front panel for
setting desired number of revolution.
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCPD – 2D
SKU: *Model No: UCPD - 2D
Strainers
Fibre Classifier (Baur Mc nett Type)
4.5 inch HD Touch Screen (1280 x 720)
Android 4.4 KitKat OS
1.4 GHz Quad Core™ Processor
20 MP front and 28 megapixel CMOS rear camera
Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt.
SKU: FW511948218
SKU: FW511948218
Strainers
Puncture Tester
This tester used to measure the rigidity and resistance against puncture
due to impact of card board and other kinds of board used for packaging
containers. Damage caused to these materials by touching of solids like
projecting object etc, can be reproduced with similarity by means of this
tester. By performing both rigidity and puncture tester for specimens from
the same lot of we can determine the co-relation between tearing and
rigidity. Mechanically operated with five nos calibrated scales
due to impact of card board and other kinds of board used for packaging
containers. Damage caused to these materials by touching of solids like
projecting object etc, can be reproduced with similarity by means of this
tester. By performing both rigidity and puncture tester for specimens from
the same lot of we can determine the co-relation between tearing and
rigidity. Mechanically operated with five nos calibrated scales
*ModelNo:UCPT-1000A
SKU: *ModelNo:UCPT-1000A
Strainers
DIGITAL GSM TESTER
This Instrument is used for measuring the basis weight (GSM) of
paper and other sheets materials by weighing a small test sample
with given dimensions. Digital DPM are showing direct GSM. This
accuracy is maintained through load cell, or other causes, which may
affect its weight.
Capacity: 0-1000, 0-2000 GSM
paper and other sheets materials by weighing a small test sample
with given dimensions. Digital DPM are showing direct GSM. This
accuracy is maintained through load cell, or other causes, which may
affect its weight.
Capacity: 0-1000, 0-2000 GSM
Accuracy: 0.2 GSM
Suitable for different size of paper 10×10, 20×20, 20×25,
25×25, 25x40cm
Power required: 220 VAC, 50 Hz
Model No: UCGT-1000D
Suitable for different size of paper 10×10, 20×20, 20×25,
25×25, 25x40cm
Power required: 220 VAC, 50 Hz
Model No: UCGT-1000D
SKU: Model No: UCGT-1000D
PULP TESTING EQUIPMENTS
Strainers
Internal Ply Bond Tester (Scott Type)
The instrument designed for determining the internal bonding strength of paper
paperboard and laminates etc, by measuring the average energy, in thousands of
foot pound required to de-laminate the specimen in two piles as described
reference standard TAPPI T-569. Dual capacity pendulum of 0-0.25 FT/LB and 0.1-
0.5 Ft/Lb. readings directly on calibrated scale. The five number specimen
preparation unit which will allow for variations of specimen thickness, with
different clamping pressure on the specimen from 50 to 200 PSI
paperboard and laminates etc, by measuring the average energy, in thousands of
foot pound required to de-laminate the specimen in two piles as described
reference standard TAPPI T-569. Dual capacity pendulum of 0-0.25 FT/LB and 0.1-
0.5 Ft/Lb. readings directly on calibrated scale. The five number specimen
preparation unit which will allow for variations of specimen thickness, with
different clamping pressure on the specimen from 50 to 200 PSI
*Attachment: Standard calibration sliding weight with sample holder.
*Double side adhesive tape width 25 mm
*ModelNo:UCPBT-5A
*Double side adhesive tape width 25 mm
*ModelNo:UCPBT-5A
*Power required: 220 VAC, 50 Hz
*Model No: UCBST- 30DH
*Model No: UCBST- 30DH
SKU: *Model No: UCBST- 30DH
Strainers
Freeness Tester (Schopper Reigler Type)
Freeness tester is intended for determining the drainage capability of beaten
pulp and is universally used to check the progress of the beating process and
confirm to the international Standard.
pulp and is universally used to check the progress of the beating process and
confirm to the international Standard.
SCAN-M3:65,lS:6213(Part iii).
Along with two measuring jar
*Model No: UCBFT – SR
Along with two measuring jar
*Model No: UCBFT – SR
SKU: *Model No: UCBFT - SR
Strainers
Digital Box compression Tester
This high quality compression strength tester is intended for testing
packaging it is expected to be an excellent alternative for all customer for
which a crush tester is to small and a conventional compression tester too
large and especially, too expensive. The compression tester consist of a
mechanical press with greatest accuracy having two compress platens of
which the lower one is firm and the top one is movable and connected to a
load cell.
packaging it is expected to be an excellent alternative for all customer for
which a crush tester is to small and a conventional compression tester too
large and especially, too expensive. The compression tester consist of a
mechanical press with greatest accuracy having two compress platens of
which the lower one is firm and the top one is movable and connected to a
load cell.
*Platform size: 600×600 mm
*Displacement: 450 mm
*Capacity: 600 Kg,
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*Displacement: 450 mm
*Capacity: 600 Kg,
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*Model No: UCCST – 1000DM
SKU: *Model No: UCCST - 1000DM
Strainers
Freeness Tester (Canadian Type)
This instrument is used for determination of freeness of wood fibre ground wood
and mechanical pulp. It measures the Canadian freeness number which is a
measurement of the drainage capacity of different pulp types. It is useful index
of the amount of mechanical treatment given to the pulp With standard screen
plate and plexiglass measuring cylinder for CSF value. 3 gram of OD fibre pulp in
aqueous suspension is drained through the fibre mat on a standard perforated
screen plate during the test into a funnel provide with a bottom and side orifice
the filtrate collected in specially graduated measuring cylinder from the side
orifice is expressed as a CSF value corresponds to millilitre
and mechanical pulp. It measures the Canadian freeness number which is a
measurement of the drainage capacity of different pulp types. It is useful index
of the amount of mechanical treatment given to the pulp With standard screen
plate and plexiglass measuring cylinder for CSF value. 3 gram of OD fibre pulp in
aqueous suspension is drained through the fibre mat on a standard perforated
screen plate during the test into a funnel provide with a bottom and side orifice
the filtrate collected in specially graduated measuring cylinder from the side
orifice is expressed as a CSF value corresponds to millilitre
*Attachment: Two measuring jar
*Model No: UCBFT – CSF
*Model No: UCBFT – CSF
SKU: *Model No: UCBFT - CSF
Strainers
Electronic Stiffness Tester
This instrument used to measure the stiffness of paper board by determining
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
the bending resistance in gram force necessary to deflect by the motor end of
38 mm wide horizontally clamped specimen with six preset test length (i.e
5,10,15,20, 25 & 50 mm). The bending angle setting up to 90 degree.
*Digital read out for Bending Force,
*Range: 0 – 10000mN *Mechanical structure: Aluminium
*Load Cell: Max load *Cabinet structure: Aluminium
*Attachment: Triple shear cutter for specimen prepration
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*ModelNo:UCST-10000D
SKU: *ModelNo:UCST-10000D
Strainers
Smoothness Tester (Bendtsen Type)
This instrument is used for testing the average smoothness, porosity
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
& softness of the paper and film by determining the time necessary
for a certain volume of air to flow through the inserted sample,
under
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
a uniform pressure. Electronic self started timer for automatic
measuring to pass through the test specimen
Attachment:
*Template for specimen prepration
*4.5 digit SSD timer
*Power required: 220 VAC, 50 Hz
*Model No: UCSPS – G
SKU: *Model No: UCSPS - G
Strainers
Fibre Classifier (Baur Mc nett Type)
4.5 inch HD Touch Screen (1280 x 720)
Android 4.4 KitKat OS
1.4 GHz Quad Core™ Processor
20 MP front and 28 megapixel CMOS rear camera
Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt.
SKU: FW511948218
SKU: FW511948218
Strainers
Automatic Sheet Press
This instrument is used for pressing and de-watering of the hand
sheet quickly made on standard sheet making machine. Its must be
uniform pressure for the distribution of pulp across area
sheet quickly made on standard sheet making machine. Its must be
uniform pressure for the distribution of pulp across area
*Pneumatic sheet press control device
*Pressing time: 6-12 min adjustable
*Working pressure: 3.5 kg/cm2
*Size: 165mm, 200mm Squire
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCASP – 612
*Pressing time: 6-12 min adjustable
*Working pressure: 3.5 kg/cm2
*Size: 165mm, 200mm Squire
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCASP – 612
SKU: *Model No: UCASP - 612
Strainers
Digital Core Collapse Tester
This instrument is used for measuring the crush strength of paper core. This is
the high quality core collapse tester is intended for testing crush strength of
core. It is expected to be an excellent alternative for all customer. The tester
consist of a mechanical stress system with greatest accuracy having two
stress jaws of which the one is movable and the lower one is firm and
connected to load cell.
the high quality core collapse tester is intended for testing crush strength of
core. It is expected to be an excellent alternative for all customer. The tester
consist of a mechanical stress system with greatest accuracy having two
stress jaws of which the one is movable and the lower one is firm and
connected to load cell.
1*Capacity: 500 Kg
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*Model No: UCCCT – 500DM
*Data transfer system through RS 232
*Power required: 220 VAC, 50 Hz
*Model No: UCCCT – 500DM
SKU: *Model No: UCCCT - 500DM
Strainers
Thickness Micrometer (Bulk Tester
The thickness of sheet is meas*Automatic dead weight with time control deviceured as distance between two
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
circular plane surface, under a steady pressure 2kg/cm2 (98.0Kpa)
for rapid and accurate measurement of thickness of paper & Paper
Board and Plastics.
*Motorized operated.
*Automatic dead weight with time control device
*Maximum thickness range: 10 mm
*Resolution: 1 Micron/0.001 mm
*Operating voltage: 220 VAC, 50 Hz
*Model No: UCTMB – 10D
SKU: *Model No: UCTMB - 10D